®
• Safety
Before using this product, read
this manual and follow all
Safety Rules and
• Assembly
• Operation
• Maintenance
• Parts
Operating Instructions.
For Missing Parts or Assembly Questions
Please Call 866-576-8388
Mon.-Fri. 7 am - 5 pm CST.
FAX 217-728-2032 or e-mail [email protected]
Missing parts will be sent UPS in 24 hours directly to your home.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
FORM NO. 49290 (2/04)
F
G
H
I
2
2
2
2
2
Strap, Tarp
S-Hook
Hook, Spring
Foam Sleeve
Rubber Cap
A
B
C
D
E
5
2
2
7
2
Bolt, 1/4" x 1-1/4"
Bolt, 1/4" x 1-1/2"
Bolt, 5/16" x 1-1/4"
Nut, 1/4" Nylock
Spacer
J
F
G
H
I
1
1
1
1
Tube, Outer Cross
Tube, Inner Cross
Tube, Base (Right)
Tube, Base (Left)
A
B
C
D
E
1
2
1
1
2
Shade, Top
Tube, Top
Rod, Support (Long)
Rod, Support (Short)
Tube, Upright
3
•
•
Slide foam sleeve onto left base tube. See figure 2.
Attach left base tube to left seat bracket. Use one
5/16” x 1-1/4” bolt from hardware package and the
previously removed original nut. Make sure seat
raises and lowers freely. Slightly loosen nuts if
seat is too tight. See figure 2.
(2) 7/16” Wrenches or Socket Wrench
(2) 1/2” Wrenches or Socket Wrench
Remove all parts and hardware package from the
carton. Identify all parts and hardware by referring to
the Carton Contents on previous page.
•
Repeat first five steps to install right base tube.
Make sure tractor seat raises
and lowers freely after attaching Sun
Shade. The tractor's safety kill switch will
not operate if seat is stuck down.
NOTE: Your tractor fender style may differ from the
one shown in the drawings. The following
instructions apply to all fender styles.
•
•
•
Raise tractor seat to access seat mounting hard-
ware.
Remove original bolt and nut from left side of seat
mount bracket.
•
Attach outer cross tube to inner cross tube using
one 1/4” x 1-1/4” bolt and one 1/4” nylock nut.
Select the hole that gives the best fit. See figure 3.
Insert supplied spacer into the seat bracket. See
figure 1.
NOTE: Most tractors use the fourth hole from the end.
•
Attach the assembled cross tubes to the right and
left base tubes using two 1/4” x 1-1/2” hex bolts
and two 1/4” nylock nuts. Tighten all bolts. See
figure 3.
4
•
Insert the upright tubes onto the right and left base
tubes, turning the upright tubes so that the small
hole shown in figure 4 faces inward. Fasten using
two 1/4” x 1-1/4” and two 1/4” nylock nuts. See
figure 4.
•
•
Unfold sun shade and locate the nylon loops found
on the mesh portion of the sun shade. The mesh is
located at the rear. See figure 6.
Hold the sun shade in front of the top tubes and
slip the nylon loops onto the ends of the top tubes.
Slide the sun shade along the top tubes, inserting
the ends of the tubes into the stitched sleeves on
each side of the sun shade. Continue until the
ends of the tubes extend out in front of the sun
shade. See figures 6 and 7.
•
Attach top tubes to the upright tubes, but do not
install mounting bolts at this time. See figure 5.
5
•
•
Install rubber caps onto the ends of both top tubes.
See figure 8.
•
•
Fasten top tubes to upright tubes using two 1/4” x
1-1/4” hex bolts and two 1/4” nylock nuts. See
figure 10.
Install the shorter of the two support rods into the
holes at the front of each top tube. See figure 8.
Insert one end of the remaining support rod into
the small hole in one of the upright tubes. Insert
the other end of the support rod into the small hole
in the other upright tube. It will be necessary to
flex the rod slightly so it can be inserted in the
second hole. See figure 10.
•
Pull the front of the sun shade top forward past the
ends of the top tubes. Pull the sun shade back
onto the tubes inserting the capped ends of the
tubes into the pockets on the front of the sun
shade. See figure 9.
•
•
•
Insert the small loop of the spring hook through the
hole at one end of the tarp strap. See figure 11.
Insert an S-hook through the other end of the tarp
strap. See figure 11.
Hook the spring hook over the end of the cross
tube and attach the S-hook to the bottom edge of
the tractor fender. See figure 11.
•
Repeat above steps for other tarp strap. Attach to
opposite end of cross tube. See figure 11.
X
6
•
•
Check the area of operation thoroughly before
using the tractor with the sun shade . The added
height of the sun shade and a reduced field of
vision require extra caution during operation.
This sun shade does not provide
protection against exhaust fumes, collision,
rollover or other accidents.
Remove the upper sun shade frame and canopy
before you transport the tractor in an open truck or
open trailer.
for low tree limbs
and other overhead objects which may
interfere with the sun shade.
transport the tractor in an
open truck or open trailer while the sun
shade is attached.
•
Read and follow the maintenance schedule and the maintenance procedures listed in this section.
MAINTENANCE SCHEDULE
Fill in dates as you
complete regular service.
Service Dates
Check for loose fasteners
Cleaning
X
X
X
•
•
Before each use, make a thorough visual check of
the sun shade for any bolts and nuts which may
have loosened. Retighten any loose bolts and nuts.
•
•
Clean the vinyl canopy thoroughly with mild liquid
soap and water. Allow canopy to dry before storing.
Store the sun shade in a clean, dry area away from
direct sunlight.
Wipe loose dirt and debris from the vinyl canopy
after each use. The vinyl canopy can be washed
using mild liquid soap and water.
7
REF. PART
QTY.
DESCRIPTION
Shade, Top
Cap, Rubber
Rod, Support (Short)
Tube, Top
Bolt, 1/4" x 1-1/4"
Nut, 1/4" Nylock
Rod, Support (Long)
Tube, Upright
Spacer
Bolt, 5/16" x 1-1/4"
REF.
NO.
PART
NO.
QTY.
DESCRIPTION
NO.
NO.
1
2
3
4
5
6
7
8
9
49279
49310
25352
49277
1509-90
47189
49305
49278
25357
43840
1
2
1
2
5
7
1
2
2
2
11
12
13
14
15
16
17
18
19
43648
49274
49284
49288
49276
49275
49245
49313
44849
49290
2
1
1
2
1
1
2
2
2
1
Bolt, 1/4" x 1-1/2"
Tube, Base (Right)
Tube, Base (Left)
Sleeve, Foam
Tube, Outer Cross
Tube, Inner Cross
Hook, Spring
Strap, Trap
S-Hook
Owner's Manual
10
8
9
10
11
Get it fixed, at your home or ours!
For repair of major brand appliances
no matter who made it, no matter who sold it!
SM
Anytime, day or night
To bring in products such as vacuums, lawn equipment and electronics
for repair, call for the location of your nearest
Anytime, day or night
For the replacement parts, accessories and owner’s manuals
SM
that you need to do-it-yourself, call
!
6 a.m. – 11 p.m. CST,
7 days a week
To purchase or inquire about a Sears Service Agreement:
7 a.m. – 5 p.m. CST, Mon. – Sat.
Para pedir servicio de reparación a domicilio,
Au Canada pour service en français:
SM
y para ordenar piezas con entrega a domicilio:
SM
(1-877-533-6937)
(1-888-784-6427)
SM
HomeCentral
® Registered Trademark / ™ Trademark of Sears, Roebuck and Co.
® Marca Registrada / ™ Marca de Fábrica de Sears, Roebuck and Co.
© Sears, Roebuck and Co.
|