®
WEATHERMASTER 8 TENT
MODEL 2000001596
6. Rotate all six Leg Poles upright and insert
Before you begin
pin on each web loop at the side locations
as shown. (Fig. 7 & 7A)
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or
sharp objects, to install your tent.
7A
Pin
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees because of potential
lightning strikes or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent
property damage or personal injury.
• For best results in windy conditions, position narrow end of
tent into the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.
Pole Descriptions
Pole
Pole
Pole
Description
Qty. Dia.
Repair Kit Replacement Kit
Long Leg Pole, steel
(w/ red marking)
2
4
19mm
19mm
N/A
N/A
5010000612
5010000622
7B
Short Leg Pole, steel
Fig. 7
Curved Ridge Pole, steel
Metal Tip
Hole in
(w/ red marking)
1
2
19mm
19mm
N/A
N/A
5010000617
5010000616
Curved Ridge Pole, steel
Window Vent Pole,
black, fiberglass
Sleeve
Window Pole
Leg Pole
7C
2
8.5mm 5010000541 5010000547
6. Assemble the two, shock-corded, black Window Poles,
then insert one into sleeve located at each end of tent.
(Fig. 7 & 7B)
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip doors. (Fig. 1)
7. Insert tapered metal tip on Window Pole into Leg Pole.
Fig. 1
NOTE: It may be necessary to gently rotate Leg Pole so the
hole will line up with the Window Pole.
8. Go to opposite end of each window pole and gradually apply
pressure to the pole forming an arch. Insert the pin into the
leg pole end at the corners of tent. (Fig. 7 & 7C)
9. Locate the plastic hooks at sides and corners of tent, then
snap onto Leg Poles to attach. (Fig. 8)
Door
2. Pull four corners of tent taut, then secure
by driving stakes through web loops at an
angle for better anchoring. (Fig. 2)
10. Locate web strap
Fig. 8
Fig. 9
with plastic hook on
the sides of each
end panel Window
Vent, then snap onto
the corner Leg Pole.
(Fig. 9)
Corner
Leg Pole
Fig. 2
3. Assemble three, steel, shock-corded,
curved Ridge Poles. Insert Ridge Pole
(with red marking) into center sleeve
on top of tent with the red trim (Fig. 3).
Insert the remaining curved Ridge Poles
into the other two sleeves on top of tent.
Fig. 3
Ridge Pole
with Red
Marking
Window Vent
Web Tent Strap
Sleeve
with Red
Trim
11. To stretch tent to finished size:
Fig. 10
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig.10);
4. Assemble six, steel, shock-corded,
Leg Poles. Push down on steel button
on tapered end and insert into end
with four holes.
NOTE: Make sure steel button locks
into third hole on pole as shown. (Fig.4)
5. Insert curved end of Leg
Poles (with red dot) into
Upper
Leg Pole
Section
• Pull up on top Leg Pole section
until tent is taut;
• Twist the lower Leg Pole clock-
wise until the button locks into
the center or lowest hole;
Button in third hole
Button
Center Hole
Lower Hole
Fig. 4
Lower
Leg Pole
Section
Ridge Pole with
Red Marking
• Repeat on remaining Leg Poles.
the ends of the RidgePole
(with red dot). Insert
curved end of remaining
short Leg Poles into the
ends of the remaining
Ridge Poles. (Fig. 5 & 6)
12. Insert plastic stakes through
web straps located on both sides
of tent, then drive in to secure.
(Fig. 11)
Sleeve
with Red
Trim
Curved End of
Long Leg Pole
Fig. 5
Fig. 11
Fig. 6
(continued on other side)
|