ELECTRIC WALL OVENS
TABLE OF CONTENTS
Welcome ................................................................. 1
Safety Instructions ............................................... 2-3
Controls at a Glance ............................................ 4-7
Function Pads ................................................ 4-5
Setting the Clock .............................................. 5
Setting the Timer .............................................. 5
Control Options............................................. 5-6
Lower Oven Controls (select models) ............. 7
Oven Light & Vent ........................................... 7
Oven Operation ................................................. 8-11
Oven Fans ........................................................ 8
Baking, Roasting and Convection Cooking ..... 8
Oven Racks and Positions................................ 9
Broiling .......................................................... 10
Clock Controlled Oven Operations.................11
Care and Cleaning ........................................... 12-15
Self-Clean Oven ........................................ 12-13
Cleaning Chart .......................................... 14-15
Maintenance ......................................................... 15
Before You Call for Service............................. 16-17
If You Need Service.............................................. 18
Warranty ............................................................... 19
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
®
IMPORTANT SAFETY INSTRUCTIONS
The following instructions are based on safety considerations
and must be strictly followed to eliminate the potential risks
of fire, electric shock, or personal injury.
• Children must be taught that the appliance and utensils
in it can be hot. Let hot utensils cool in a safe place, out
of reach of small children. Children should be taught
that an appliance is not a toy. Children should not be
allowed to play with controls or other parts of the unit.
Installation and Repair
• Have your appliance installed and properly grounded by
a qualified installer according to the installation instruc-
tions.
• CAUTION: NEVER store items of interest to children
in cabinets above an appliance. Children climbing on
the appliance or on the appliance door to reach items
could be seriously injured.
• To ensure proper operation and avoid possible injury or
damage to unit do not attempt to adjust repair, service, or
replace any part of your appliance unless it is specifically
recommended in this book. All of the servicing should be
referred to a qualified installer or servicer.
AboutYour Appliance
• To prevent potential hazard to the
user and damage to the appliance,
never use appliance to heat or warm
a room.
To Prevent Fire or Smoke Damage
• Do not obstruct the flow of air by
• Be sure all packing materials are removed from the ap-
blocking the oven vent.
pliance before operating it.
• DO NOT TOUCH HEATING ELEMENTS OR INTE-
RIOR SURFACES OF OVEN. Heating elements may
be hot even though they are dark in color. Interior sur-
faces of any oven become hot enough to cause burns.
During and after use, do not touch, or let clothing or
other flammable materials contact heating elements or
interior surfaces of oven until they have had sufficient
time to cool. Other surfaces of the appliance may be-
come hot enough to cause burns – among these sur-
faces are: oven vent openings and surfaces near these
openings, oven doors, windows of oven doors.
• Keep area around appliance clear and free from combus-
tible materials. Flammable materials should not be stored
in an oven.
• Many plastics are vulnerable to heat. Keep plastics away
from parts of the appliance that may become warm or
hot.
• To prevent grease fires, do not let cooking grease or other
flammable materials accumulate in or near the appliance.
• Do not use the oven as a storage area for food or cooking
utensils.
• CAUTION: NEVER use an appliance as a step to reach
cabinets above. Misuse of appliance doors, such as step-
ping, leaning or sitting on the door, may result in pos-
sible tipping of the appliance, breakage of door, and
serious injuries.
• Many aerosol-type spray cans are EXPLOSIVE when
exposed to heat and may be flammable. Avoid their use
or storage near the oven.
• Do not touch a hot oven light bulb with a damp cloth as
the bulb could break. Should the bulb break, discon-
nect power to the appliance before removing bulb to
avoid electrical shock.
In Case of Fire
• Use dry chemical or foam-type extinguisher or baking
soda to smother fire or flame. Never use water on a grease
fire.
• A fan should be heard during some bake, convect bake,
and all broil and cleaning operations. If you do not hear
the fan, call an authorized servicer.
1. Turn off appliance to avoid spreading the flame.
2. NEVER pick up or move a flaming pan.
• NEVER use aluminum foil to cover an oven rack or
oven bottom. Misuse could result in risk of electric
shock, fire, or damage to the appliance. Use foil only as
directed in this guide. Do not allow aluminum foil to
contact heating element.
3. Smother fire or flame by closing the oven door.
Child Safety
• NEVER leave children alone or unsupervised near the
appliance when it is in use or is still hot. Children should
never be allowed to sit or stand on any part of the appli-
ance as they could be injured or burned.
2
IMPORTANTSAFETYINSTRUCTIONS(continued)
Cleaning Safety
Cooking Safety
• Turn off all controls and wait for appliance parts to cool
before touching or cleaning. Clean with caution. Use
care to avoid steam burns if a wet sponge or cloth is
used to wipe spills on a hot surface. Some cleaners can
produce noxious fumes if applied to a hot surface.
• NEVER heat an unopened food container in the oven. Pres-
sure build-up may cause container to burst resulting in se-
rious personal injury or damage to the appliance.
• Use dry, sturdy potholders. Damp potholders may cause
burns from steam. Dish towels or other substitutes should
never be used as potholders because they can trail across
hot elements and ignite or get caught on appliance parts.
• Clean only parts listed in this guide.
• NEVER wear loose fitting or long hanging-sleeved apparel
while cooking. Clothing may ignite and cause burns if gar-
ment comes in contact with heating el-
ements.
Self-Clean Oven
• Do not clean door gasket. The door gasket is essential
for a good seal. Care should be taken not to rub, dam-
age, or move the gasket.
• Always place oven racks in the desired
positions while oven is cool. If a rack
must be moved while hot, use a dry
potholder. Do not let potholder contact
hot element in oven.
• Do not use oven cleaners or oven liners of any kind in
or around any part of the self-clean oven.
• Before self-cleaning the oven, remove broiler pan, oven
racks and other utensils, and wipe off excessive
spillovers to prevent excessive smoke or flare ups.
• Use care when opening the oven door. Let hot air or steam
escape before removing or replacing food.
• CAUTION: NEVER leave food or cooking utensils,
etc. in the oven during the self-clean cycle.
• PREPARED FOOD WARNING: Follow food manu-
facturer’s instructions. If a plastic frozen food container and/
or its cover distorts, warps, or is otherwise damaged during
cooking, immediately discard the food and its container.
The food could be contaminated.
Important Safety Notice
and Warning
• Always turn off all controls when cooking is completed.
The California Safe Drinking Water and Toxic Enforce-
ment Act of 1986 (Proposition 65) requires the Governor
of California to publish a list of substances known to the
State of California to cause cancer or reproductive harm,
and requires businesses to warn customers of potential ex-
posures to such substances.
Utensil Safety
• Follow the manufacturer’s directions when using oven cook-
ing bags.
Users of this appliance are hereby warned that when the
oven is engaged in the self-clean cycle, there may be some
low-level exposure to some of the listed substances, in-
cluding carbon monoxide. Exposure to these substances
can be minimized by properly venting the oven to the out-
doors by opening the windows and/or door in the room
where the appliance is located during the self-clean cycle.
• This appliance has been tested for safe performance using
conventional cookware. Do not use any devices or acces-
sories that are not specifically recommended in this manual.
Do not use add-on oven convection systems. The use of
devices or accessories that are not expressly recommended
in this guide can create serious safety hazards, result in per-
formance problems, and reduce the life of the components
of the appliance.
IMPORTANT NOTICE REGARDING PET BIRDS:
Never keep pet birds in the kitchen or in rooms where the
fumes from the kitchen could reach. Birds have a very sen-
sitive respiratory system. Fumes released during an oven
self-cleaning cycle may be harmful or fatal to birds. Fumes
released due to overheated cooking oil, fat, margarine and
overheated non-stick cookware may be equally harmful.
• Only certain types of glass, glass/ceramic, ceramic, earth-
enware, or other glazed utensils are suitable for oven ser-
vice without breaking due to the sudden change in tem-
perature. Follow utensil manufacturer’s instructions when
using glass.
SaveTheseInstructionsforFutureReference
3
Controls at a Glance
The control panel is designed for ease in programming. The display window on the electronic control shows time of day,
timer and oven functions. Indicator words flash to prompt your programming steps.
CANCEL
HR
°
00:00 000
BAKE
LOCK
DELAY COOK STOP TIMER CLEAN ROAST BROIL
CONVECT
CONTROL
LOCK
BAKE
CLEAN
TIMER
CLOCK
BROIL
COOK TIME
STOP TIME
NOTE: Styling and features may differ slightly depending on the model. Control panel shown above includes Convect
Bake feature.
Function Pads
BROIL Pad
Use for top browning and broiling.
• Press the desired pad.
• Press, or press and hold, these pads to enter time,
1. Press BROIL pad.
oven temperature or to select HI or LO broil.
2. Press
or
pad for HI or LO broil.
• Press the CANCEL pad to cancel all operations
See page 10 for additional information.
CANCEL
except the TIMER and CLOCK.
NOTE: If more than 30 seconds elapse between pressing a
function pad and a or pad, the program will be
canceled and the display will return to the time of day.
CLEAN Pad
Use to set self-clean cycle.
1. Press CLEAN pad. “– – : – – ” will appear in the
CONVECT Pad (select models)
Use for convection baking or roasting.
1. Press CONVECT pad.
display.
2. Press
or
pad. “3:00” hours of cleaning time
will automatically be entered.
3. If more or less cleaning time is desired, press
2. Press
or
pad once and 325° will appear in the
or
pad to select times between 2 to 4 hours.
display. Continue pressing until the desired oven tem-
perature appears in the display.
See pages 12-13 for additional information.
See page 8 for additional information.
COOK TIME/STOP TIME Pads
Use to program the oven to start and stop automatically.
BAKE Pad
Use for baking or roasting.
1. PressCOOKTIMEpadandenterthedesiredcooking
time.
1. Press BAKE pad.
2. Press
or
pad once and 350° will appear in the
2. Press the BAKE or CONVECT (select models) pad
display. Continue pressing until the desired oven tem-
perature appears in the display.
and enter oven temperature.
3. To delay the start of cooking, press the STOP TIME
See page 8 for additional information.
pad and enter the time you wish the oven to turn off.
See page 11 for additional information.
4
Controls at a Glance (continued)
Example of timer set for five minutes:
CONTROL LOCK Pad
HR
°
00:050 0 0
The control touch pads can be locked to prevent unwanted
use. They will not function when locked.
BAKE
DELAY COOK STOP TIMER CLEAN ROAST BROIL
If an oven function is currently being used, the controls
cannot be locked.
• The timer will start automatically after four seconds.
A flashing colon indicates that the timer is in use
during another function’s operation.
The current time of day will remain in the display when this
feature is activated.
• The last minute of the countdown will be displayed as
seconds.
Setting Control Lock:
3. At the end of the time set, one long beep will sound. (To
1. Press and hold the CONTROL LOCK pad for several
changethenumberoftimerreminderbeeps,seebelow.)
seconds.Thecontrolwillbeeponceindicatingitislocked.
To cancel: Press and hold the TIMER pad for several
seconds. The time of day will reappear in the display.
• OFF will appear in the display for 15 seconds if any pad
is pressed.
To Cancel: Press and hold the CONTROL LOCK pad for
several seconds. The indicator word OFF will disappear in
the display.
Control Options
Timer Beep Option
Setting the CLOCK
1. Press CLOCK pad.
You have a choice of three “end of timer” reminder
signals.
Option 1. One beep at the end of the timer operation, then,
one beep every 30 seconds for the next five minutes or
until the CANCEL pad is pressed.
2. Press or press and hold
or
pad until the correct
time of day appears in the display.
The display will flash when electrical power is first supplied
to the oven or if there has been a power failure.
Option 2. One beep at the end of the timer operation, then,
one beep every minute for the next 12 hours or until the
CANCEL pad is pressed.
To recall the time of day when another function is displayed,
press the CLOCK pad.
Option3. (defaultoption)Onebeepattheendofthetimer
operation, then, no other beeps.
Clock time cannot be changed when the oven has been
programmed for clock controlled cooking, self-clean or
delayed self-clean.
Setting the Timer Beeps
1. Press the TIMER and CANCEL pads at the same time
and hold for several seconds.
Setting the TIMER
Thetimercanbesetfromoneminute(0HR:01)upto99hours
and 59 minutes (99:59).
• A single beep will sound.
• Display will show current option - 1, 2 or 3.
The timer can be used independently of any other oven
activity and it can be set while another oven function is
operating. THE TIMER DOES NOT CONTROL THE
OVEN.
2. Press the
or
pad to select the option number you
wish. The current time of day will reappear in the
display after four seconds.
1. Press the TIMER pad.
• The indicator word TIMER will flash.
2. Press or press and hold the
or
pad until the correct
time appears in the display.
5
Clock Controlled
Automatic Oven Turn Off Option
Oven Cooking Beep Option
The oven will automatically turn off after 12 hours, if you
accidentally leave it on. You can deactivate this feature,
if desired.
You have a choice of three “end of timed cook” reminder
signals for programmed cooking.
To Eliminate 12 Hour Turn Off
Option 1. (default option) Four beeps at the end of cooking,
then, one beep every 30 seconds for the next five minutes or
until the CANCEL pad is pressed.
1. Press the CLOCK pad and hold for several seconds.
2. Press and hold the
or
pad until 8888 appears
Option 2. Four beeps at the end of cooking, then, one beep
everyminuteforthenext12hoursoruntiltheCANCELpad
is pressed.
in the display. Current time of day will reappear in the
display after four seconds.
To restore: Repeat steps 1 and 2. “12” will appear briefly
in the display followed by the current time of day.
Option 3. Four beeps at the end of cooking, then, no other
beeps.
Oven Temperature
Adjustment Option
Setting Clock Controlled Oven Cooking Beeps
1. Press COOK TIME and CANCEL pads at the same time
and hold for several seconds.
Youmayadjusttheoventemperatureifyouthinktheoven
isnotbakingcorrectly. Todecidehowmuchtochangethe
temperature, set the temperature 25 degrees higher or
lower than your recipe recommends, then bake. The
results of the “test” should give you an idea of how much
to adjust the temperature.
• A single beep will sound.
• Display will show current option - 1, 2 or 3.
2. Press the
or
pad to select the option number you
wish. The current time of day will reappear in the display
after four seconds.
To Adjust the Oven Temperature
1. Press the BAKE pad.
Cancel Clock Display Option
2. Enter 550° by pressing
pad.
3. Press and hold the BAKE pad for several seconds until
If you prefer that the time of day not be displayed when the
oven is not operating:
0° appears in the display.
To set: Press CLOCK and CANCEL pads at the same time
and hold for several seconds. The time of day will disappear in
the display.
• If the oven temperature was previously adjusted,
the change will be displayed. For example, if the
oven temperature was reduced by 15°, the display
will show -15°.
When clock display is not shown, press CLOCK pad to briefly
recall the time of day, if desired.
4. Press and hold the
or
pad to change the
temperature. Each time a pad is pressed, the tempera-
ture changes by 5°.
To restore:Press the CLOCK and CANCEL pads at the same
timeandholdforseveralseconds. Thetimeofdaywillreappear
in the display.
• The oven temperature can be increased or de-
creased by 5 ° increments up to 35 °.
NOTE: Clock display is always displayed during any cooking
operation.
5. The time of day will automatically reappear in the
display.
It is not necessary to readjust the oven temperature if there
is a power failure or interruption. Broiling and cleaning
temperatures cannot be adjusted.
6
Controls at a Glance (continued)
Lower Oven Controls (select models)
Oven Light
The oven light automatically comes on whenever
the oven door is opened. Push the switch on the
control panel to turn it on and off when the oven
door is closed.
Setting the Controls
OVEN SET
OFF
OVEN TEMP
OFF
Oven
Indicator
Light
BROIL
Oven Vent
500
WARM
200
Whentheovenisinuse, theareaneartheovenventmay
feel warm to the touch. Do not block the vent opening
for best baking results.
BAKE
BROIL
450
400
250
The oven vent is located below the control panel on your
wall oven.
350
300
The OVEN SET knob determines the type of oven opera-
tion. Turn this knob to the desired setting. The oven will not
operate if the OVEN SET knob is left in the OFF position.
The OVEN TEMP knob is used to set the oven tempera-
ture. Always turn this knob just to the desired temperature.
Do not turn to a higher temperature and then back.
Oven Indicator Light
The oven indicator light, located on the control panel be-
tween the Oven Set and Oven Temp knobs, turns on when-
ever the lower oven turns on.
When the oven reaches the preset temperature, the indicator
light turns off. The oven indicator light will then turn off
and on as the oven elements cycle off and on.
7
Oven Operation
4. Allow 8-15 minutes for the oven to preheat.
• A single beep will indicate that the oven has
preheated.
Baking, Roasting and
Convection Cooking
• The PREHEAT indicator will turn off.
Every oven has its own characteristics. You may find that the
cooking times and temperatures vary slightly from your old
oven. This is normal.
5. Checkcookingprogressattheminimumcookingtime.
Cook longer if needed.
Oven Fans
6. Press CANCEL pad and remove food from the oven.
A cooling fan will automatically turn on during cleaning,
broiling and some baking operations. It is used to help keep
internal parts on the control panel cool. The fan will automati-
cally turn off when parts have cooled. The fan may continue to
operate after the oven has been turned off. This is normal.
NOTE: If you forget to turn off the oven, it will
automatically turn off at the end of 12 hours. If you
wish to deactivate this feature, see page 6.
A convection fan (select models) is used to circulate hot air in
the oven when the convection feature is selected. It automati-
cally turns on whenever the CONVECT pad is pressed and will
turn off when CONVECT is canceled.
Notes . . .
•
If more than 30 seconds elapse between pressing
a function pad and pressing a or pad,
NOTE: The convection fan will automatically stop whenever
the oven door is opened.
the display will return to the previous display.
•
To recall the set temperature during preheat, press
the appropriate BAKE or CONVECT (select
models) pad. The set temperature will be dis-
played briefly and then return to the on-going
program.
Setting the Controls for Baking,
Roasting and Convection Cooking*
* Convection feature available on select models only.
1. Press BAKE or CONVECT pad.
• BAKE or CONVECT will flash in display.
• 000 will light in display.
•
•
To change the oven temperature during cooking,
press the appropriate BAKE or CONVECT
(select models) and the appropriate
pads for the desired oven temperature.
or
• When convection cooking is selected, a fan icon
also appear.
will
As a general rule when convection baking, set
the oven temperature 25°F lower than the con-
ventional recipe or prepared mix directions.
Times will be similar to a few minutes less than
directions.
2. Press or press and hold the
or
pad to select oven
temperature.
• 350° is set when either pad is pressed. When convection
cooking, 325° is set.
• Oven temperature can be set from 100° to 550°.
•
•
When convection is used to roast meats, roasting
times are generally 25-30% less. (Maintain con-
ventional roasting temperatures.)
3. There will be a four second delay before oven turns on.
When the oven turns on:
• PREHEAT indicator will light in the display.
• The BAKE symbol will light in display.
• When convection cooking, the fan icon will begin to
rotate.
For additional baking, roasting and convection
cooking tips plus a roasting chart with recom-
mended roasting temperatures and times, see
“Cooking Made Simple” booklet.
• 100° or the actual oven temperature will appear in
the display.
• The temperature will increase by 5° until the oven
reaches the preselected temperature.
BAKE
SYMBOL
PREHEAT
INDICATOR
HR
°
1 0 0
05:30
BAKE
LOCK
DELAY COOK STOP TIMER CLEAN ROAST BROIL
8
Oven Operation (continued)
Oven Racks
Rack Position #4o (offset rack on #4):
Most broiling.
Single convection ovens are equipped with two flat and one
offset rack.
Rack Position #3:
Some baked goods.
Single non-convection ovens are equipped with one flat and
one offset rack.
Rack Position #3o (offset rack on #3):
Most baked goods, pies, cakes and cookies.
Double ovens are equipped with one flat and one offset rack
for each oven.
Rack Position #2:
Roasting small cuts of meat, cakes in tube or bundt pans,
casseroles.
Toremove:Pullforwardto
the “stop” position; lift up
on the front of the rack and
pull out.
Rack Position #2o (offset on #2):
Roasting, loaves of bread, angel food cake.
Rack Position #1:
Largecutsofmeatandturkey,custardpie,dessertsouffle.
To replace: Place rack on
theracksupportintheoven;
tiltthefrontendupslightly;
sliderackbackuntilitclears
the lock-stop position;
lower front and slide into
the oven.
Multiple Rack Cooking:
Two racks (Convection or conventional cooking):
For cookies use #1 and #4o. For cakes use #2 and #4o.
Three racks (convection cooking only): Use #1, #3o, #4.
(See illustration at left.)
Rack Positions
Notes . . .
•
The use of the offset rack is denoted in the list above
as an “o” after the rack position number.
•
Do not cover an entire rack with aluminum foil or
place foil on the oven bottom. Baking results will be
affected and damage may occur to the oven bottom.
Three rack convection cooking (select models).
9
Broiling
For best results, use a pan designed for broiling. For addi-
tional broiling tips, see “Cooking Made Simple” booklet.
6. Follow the suggested times in the broiling chart below.
Meat should be turned once about halfway through its
cooking time.
7. After broiling, turn the OVEN TEMP and OVEN SET
Setting the Controls for Broiling
knobs to OFF.
1. Place the oven rack on the recommended rack position
shown in the broiling chart.
Broiling Chart
2. Press the BROIL pad.
Chart time based on a preheated broil element using the “HI” setting
•
•
BROIL will flash in the display.
000 will light in the display.
Rack
Minutes/Side (Approx.)
3. Press the
pad to select HI (high) broil or the
pad
Foods
Position* 1st Side
2nd Side
to set LO (low) broil.
Beef
•
•
Select HI broil for normal broiling.
Select LO broil for low temperature broiling of
longer cooking foods such as poultry.
Steak (1"):
Medium
Well
4o
4o
9
11
7
8
3
4
Hamburgers ( / "):
4. There will be a four second delay before oven turns on.
Medium
Well
4o
4o
5
6
3-4
4-5
When oven turns on:
•
The BROIL symbol will light in display
.
Pork
5. For optimum browning, preheat broil element for 3-4
Chops (1/2")
Chops (1")
Ham Slice
4o
3
4o
7
10-11
4
5-6
9-10
2-3
minutes before adding food.
6. Place food in the oven. Leave oven door opened to the
broil stop position (about four inches). Follow the
suggested broiling times in the chart to the right.
Poultry
Breast Halves
(Bone-in)
3
11-12
8-10
9-11
7. Turn meat once about half way through cooking.
8. Press CANCEL pad. Remove food and broiler pan from
Seafood
Fish Steaks,
Buttered (1")
the oven.
4o
(no turning)
*An "o" after the rack number implies that the offset rack
should be used.
Setting the Lower Oven Controls
for Broiling (select models)
Note: This chart is a suggested guide. The times may vary with
1. Place the oven rack on the recommended rack position
food being cooked.
shown in the broiling chart.
2. Turn OVEN TEMP knob to BROIL or, for lower tem-
Notes . . .
perature broiling, to 450°.
•
Lower temperature broiling is used to avoid excessive
browning of longer cooking foods such as poultry.
•
•
•
If more than 30 seconds elapse between pressing the
BROIL pad and the or pad, the oven is not set
and the display will return to the previous display.
3. Turn OVEN SET knob to BROIL.
•
NOTE: Oven will not operate if the OVEN SET knob
A cooling fan will automatically turn on during
broiling. If it does not operate, contact an autho-
rized servicer.
is left in the OFF position.
4. Preheat broil element for 3-4 minutes.
Expect broil times to increase and browning to be
slightly lighter if appliance is installed on a 208 volt
circuit.
5. Broil with the oven door open about four inches.
10
Oven Operation (continued)
7. Press CANCEL pad. Beeps will stop and time of day
CAUTION:
will reappear in display. Remove food from oven.
•
•
Clockcontrolledcookingisnotrecommendedforbaked
items that require a preheated oven, such as cakes,
cookies, pies and breads.
NOTE: See page 6 if you wish to change the end of
cooking reminder beeps.
Highly perishable foods such as dairy foods, pork,
poultry or seafood are not recommended for clock
controlled cooking with a delayed start.
To Delay the Start and Turn Off Automatically:
1 - 4. Follow preceding steps 1 - 4.
5. Press STOP TIME pad.
•
STOP TIME will flash in display.
Clock Controlled
Oven Operations
a. Press or press and hold
of day you wish the oven to turn off.
b. Press CLOCK pad.
or
pad to enter time
The clock controlled oven cooking feature is used to turn the
oven off at a preset time of day or delay the start and then turn
off the oven.
•
Time of day will reappear in the display.
c. DELAY BAKE will remain in display to show the
oven is set for a delayed cook operation.
The clock must be functioning and set at the correct time of
day for this feature to operate correctly.
HR
°
3 5 0
01 :30
BAKE
LOCK
The feature can be used with either oven cooking or self-
cleaning. See page 13 for instructions on delaying the start of
a clean cycle.
DELAY COOK STOP TIMER CLEAN ROAST BROIL
HR
°
3 5 0
10 :30
BAKE
LOCK
DELAY COOK STOP TIMER CLEAN ROAST BROIL
Setting the Controls
ToStartImmediatelyandTurnOffAutomatically:
6. At the end of the delayed period, the DELAY indicator
word will go off and the oven will begin to heat.
1. Press the COOK TIME pad.
•
•
0:00 will light in display.
COOK TIME will flash in the display.
7. At the end of the programmed COOK TIME, the oven
will turn off. Four beeps will sound and END will light
inthedisplay.Abeepwillsoundevery30secondsforthe
next 5 minutes.
2. Press or press and hold
or
pad to enter cooking time.
3. Press BAKE or CONVECT pad.
8. Press CANCEL pad. Beeps will stop and time of day
•
•
000 will light in display.
BAKE or CONVECT will flash in display.
will reappear in display. Remove food from oven.
NOTE: See page 6 if you wish to change the end of
cooking reminder beeps.
NOTE: If BAKE or CONVECT pad is not selected in 4
seconds, beeps will sound.
Notes . . .
4. Press or press and hold
or
pad to enter oven
temperature.
•
If more than 30 seconds elapse between pressing the
BAKE pad and setting a temperature, the display will
return to the time of day.
5. When the oven turns on, the oven temperature and the
BAKE symbol will light in display.
•
It is not necessary to set a start time. Control will
determine when to turn the oven on based on the cook
time you set.
6. At the end of the programmed COOK TIME, the oven
will turn off. Four beeps will sound and END will light in
the display. A beep will sound every 30 seconds for the
next 5 minutes.
11
Care and Cleaning
Self-Clean Oven
Wipe up sugary and acid spillovers such as sweet pota-
toes, tomato or milk-based sauces. Porcelain enamel is
acid resistant, not acid proof. The porcelain finish may
discolor if acid spills are not wiped up prior to a self-
clean cycle.
CAUTION:
•
It is normal for parts of the wall oven to become hot
during a clean cycle. Therefore, during a clean cycle,
avoid touching the oven vent area, oven door and
window.
Setting the Controls for Self-Clean
1. Close oven door.
The self-clean cycle uses above normal cooking temperatures
to automatically clean the entire oven interior.
2. Press CLEAN pad.
It is normal for flare-ups, smoking or flaming to occur during
cleaning if the oven is heavily soiled. It is better to clean the
oven regularly rather than to wait until there is a heavy build-
up of soil in the oven.
• “- - : - -” will light in the display.
• CLEAN will flash in the display. LOCK indicator
word will appear.
• Door cannot be opened when LOCK is displayed.
• If door is not closed or locked, beeps will sound and
“door” will flash in the display.
During the cleaning process, the kitchen should be well
ventilated to help eliminate normal odors associated with
cleaning.
3. Press
clean time.
or
pad to select clean time or change
Do not use commercial oven cleaners on the self-clean oven
finish or around any part of the oven as they will damage the
finish or parts.
• Oven is preset to clean for 3 hours. Or,
• Select 2 hours for light soil up to 4 hours for heavy
soil.
Before Self-Cleaning
4. When the oven turns on the clean symbol will light in
the display.
CLEAN SYMBOL
Turn off the oven light before cleaning as the light may burn
out during the clean cycle.
HR
°
03:00 0 0 0
Remove broiler pan, all pans and the oven racks from the
oven. The oven racks will discolor and may not slide easily
after a self-clean cycle.
BAKE
LOCK
DELAY COOK STOP TIMER CLEAN ROAST BROIL
Clean oven frame, door frame
(area outside the door gasket) and
around the opening in the door
gasket with a nonabrasive clean-
ing agent such as Bon Ami or de-
tergent and water. These areas are
not exposed to cleaning tempera-
tures and should be cleaned to
prevent soil from baking on dur-
ing the clean cycle.
5. About one hour after the clean cycle ends, the LOCK
indicator word will turn off. The oven door can be
opened.
HR
°
3 5 0
10 :00
BAKE
LOCK
DELAY COOK STOP TIMER CLEAN ROAST BROIL
LOCK IS STILL ENGAGED.
DOOR CANNOT BE
OPENED UNTIL LOCK IS
NO LONGER DISPLAYED.
To prevent damage, do not clean or rub the gasket around
the oven door. The gasket is designed to seal in heat during
the clean cycle.
Wipe up excess grease or spillovers from the oven bottom to
prevent excessive smoking, flare-ups or flaming during the
clean cycle. For ease of cleaning, the heating element can be
lifted slightly (1 to 11/2 inches).
12
Care & Cleaning (continued)
After Self-Cleaning
Notes. . .
About one hour after the end of the clean cycle, the LOCK
indicator word will turn off. At this point, the door can be
opened.
•When the LOCK indicator word lights in the display,
the door cannot be opened. To prevent damage to the
door, do not force door open when the LOCK indicator
word is displayed.
Some soil may leave a light gray, powdery ash which can
be removed with a damp cloth. If soil remains, it indicates
that the clean cycle was not long enough. The soil will be
removed during the next clean cycle.
•A fan will automatically turn on during the self-
clean cycle and will automatically turn off after the
clean cycle when the oven has cooled. If it does
not operate, contact an authorized servicer.
If the oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and embossed rack
supports with a small amount of vegetable oil to restore
ease of movement.
•If more than 30 seconds elapse between pressing the
CLEAN pad and pressing a
or
pad, the
program will automatically return to the previous
display.
A white discoloration may appear after cleaning if acid or
sugary foods were not wiped up before the clean cycle.
This discoloration is normal and will NOT affect perfor-
mance.
•The first few times the oven is cleaned, some smoke
and odor may be detected. This is normal and will lessen
or disappear with use. If the oven is heavily soiled, or
if the broiler pan was accidently left in the oven,
excessive smoke and odor may occur.
To Delay the Start of a Clean Cycle:
1 - 3. Follow steps 1-3 on previous page.
4. Press STOP TIME pad.
•As the oven heats and cools, you may hear sounds of
metal parts expanding and contracting. This is normal
and will not damage your appliance.
a. Press
or
pad to select the time of day you
wish the oven to turn off.
b. Press CLOCK pad and time of day will reappear in
display.
c. DELAY CLEAN will remain in display to show the
oven is set for delayed clean operation.
5. When the oven turns on the clean symbol will light in the
display.
6. About one hour after the clean cycle ends, the LOCK
indicator word will turn off. The oven door can be
opened.
To Cancel a Clean Cycle:
1. Press CANCEL pad.
2. If LOCK is NOT displayed, open oven door.
If LOCK is displayed, allow oven to cool about one hour
then open oven door.
13
Cleaning CAUTIONS:
•
Be sure appliance is off and all parts are cool before
handling or cleaning. This is to avoid damage and
possible burns.
•
To prevent staining or discoloration, clean appliance
after each use.
If a part is removed, be sure it is correctly replaced.
•
Cleaning Chart
Parts
Cleaning Procedure
Broiler Pan
and Insert
Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.
•
•
•
Place soapy cloth over insert and pan; let soak to loosen soil.
Wash in warm soapy water. Use soap filled scouring pad to remove stubborn soil.
Broiler pan and insert can be cleaned in dishwasher.
Control Panel
•
To activate “Control Lock” for cleaning , see page 5.
• Wipe with a damp cloth. Dry thoroughly.
•
•
Glass cleaners may be used if sprayed on a cloth first. Do Not Spray Directly on the Panel.
Do not use other cleaning sprays, abrasive cleaners or large amounts of water on the panel.
Glass
•
Wash with soap and water or glass cleaner. Avoid using excessive amounts of water which
may seep under or behind glass.
Do not use abrasive cleaners.
- Oven window
- Oven door
(select models)
•
Metal Finishes
- Oven Trim
• Wash with soap and water, glass cleaners, or mild liquid sprays. Avoid using excessive amounts
of water.
• Remove stubborn soils with nonabrasive cleaners such as Bon Ami* or a baking soda and water
paste; rinse and dry. Do not use abrasive cleaners.
Oven Interior
Manual Clean (lower oven only, select models)
• Clean frequently using mild abrasive cleaners and a plastic pad. Do not use metallic scouring
pads because they will scratch the surface.
• When using commercial oven cleaners, follow the manufacturer’s instructions.
Self-Clean
• Wipe up sugary and acid spillovers such as lemon juice, tomato sauce or milk-based sauces.
Porcelain enamel is acid resistant, not acid proof. The porcelain finish may discolor if acid
spills are not wiped up prior to a self-clean cycle.
• See pages 12 and 13 for information on the self-clean oven.
• To remove occasional spillovers between cleanings, use a plastic, soap-filled scouring pad;
rinse well.
Oven Racks
• Rub with a sponge or cloth using one of the following cleaners: Bon Ami, Soft Scrub or
Comet*. Rinse and dry.
• For hard to remove soils, use a dampened soap-filled scouring pad. Rinse and dry.
• Racks will permanently discolor and may not slide smoothly if left in the oven during a self-
clean operation. If this occurs, wipe the rack and embossed rack supports with a small amount
of vegetable oil to restore ease of movement, then wipe off excess oil.
14
Care & Cleaning (continued)
Cleaning Chart -- continued
Parts
Cleaning Procedure
Plastic Finishes
- Door Handle Area
• Wash with soap and water or mild liquid sprays and a soft cloth. Do not use abrasive cleaners or
oven cleaners on plastic finishes.
• To prevent staining or discoloration, wipe up fat, grease or acid (tomato, lemon, vinegar, milk,
fruit juice, marinade) immediately with a dry paper towel or cloth.
• Never use oven cleaners, abrasive or caustic liquid or powdered cleansers on plastic finishes.
These cleaning agents will scratch or mar finish.
Brushed Chrome
(select models)
• When cool, wash with soapy water, rinse and buff the surface.
• For heavier soil, use a mild abrasive cleaner, rubbing with the grain to avoid streaking the
surface. Rinse and buff.
• To prevent scratching, do not use abrasive or caustic agents.
• To restore luster and remove streaks, follow with Stainless Steel Magic Spray*
(Part #20000008)**.
Chrome will permanently discolor if soil is allowed to bake on.
* Brand names are trademarks of the respective manufacturers.
** To order direct, call 1-800-688-8408.
Maintenance
Oven Light
Oven Window
To protect the oven door window:
Before replacing light bulb, DISCONNECT POWER TO
OVEN. Be sure bulb is cool. Do not touch a hot bulb with a
damp cloth as the bulb may break.
1. Do not use abrasive cleaning agents such as steel
wool scouring pads or powdered cleansers as they
may scratch the glass.
To replace oven light:
2. Do not hit the glass with pots, pans, furniture, toys, or
Use a dry potholder and very carefully unscrew bulb cover
and bulb. Replace with a 40 watt, oven-rated appliance bulb.
Bulb with a brass base is recommended to prevent fusing of
bulb into socket.
other objects.
3. Do not close the oven door until the oven racks are in
place.
Scratching, hitting, jarring or stressing the glass may
weaken its structure causing an increased risk of break-
age at a later date.
Replace bulb cover and reconnect power to oven. Reset
clock.
15
Before You Call For Service
Check these points if . . .
•check for a blown fuse or a tripped circuit breaker.
•check if oven is properly connected to electric outlet.
The oven fails
to operate.
Clock, indicator words,
and/or lights operate
but oven does not heat.
•the controls may have been set incorrectly.
•clock controls may be set for a delayed bake function.
•the Oven Control Lockout may have been set. (See page 5.)
•the light bulb is loose or defective.
•check power supply, circuit breaker or fuse.
•the oven light does not work during self-cleaning process.
The oven light
and/or clock does
not function.
There is a strong odor
or light smoke when
oven is turned on.
•this is normal for a new wall oven and will disappear after a few uses. Initiating a
clean cycle will “burn off” the smells more quickly. Turning on a ventilation fan will
help remove the smoke and/or odor.
•excessive food soils on the oven bottom. Use a self-clean cycle.
Oven will not activate
•controls may be improperly set.
•check if set for delayed start.
the self-cleaning process.
•oven may need longer cleaning time.
Oven did not
clean properly.
•excessive spills were not removed prior to self-cleaning process.
•control may be improperly set.
•check rack position. (See page 10.)
•voltage into house may be low.
•broil element was not preheated.
Foods do not
broil properly.
•oven door was closed during broiling. Leave the door open to the first stop position.
Baked food is
burned or too
brown on top.
•food may be positioned incorrectly in oven. (See “Cooking Made Simple” booklet.)
•oven not preheated properly.
•the oven may be installed improperly.
•check the oven rack with a level.
Foods bake unevenly.
•stagger pans, do not allow pans to touch each other or oven wall.
•check instructions for suggested placement of pans on oven rack. (See“Cooking
Made Simple” booklet.)
Oven door will
not unlock.
•oven may not have cooled to safe temperature after self-cleaning process.
16
Before You Call for Service (continued)
•the pans being used may not be of the size or material recommended for best results.
(See “Cooking Made Simple” booklet).
Oven baking results
are less than expected.
•there may not be sufficient room around sides of the pans for proper air circulation
in the oven.
•check instructions for preheating, rack position and oven temperature.
•check oven temperature when convection baking (select models). Decrease
conventional baking temperatures by 25° F.
•oven thermostat calibration may differ between old and new ovens. Follow recipe
and use the directions in this guide before calling for service since the calibration on
the previous oven may have drifted to a too high or too low setting. (See p. 6 -
Oven Temperature Adjustment.)
Baking results differ
from previous oven.
The cooling fan continues
to operate after the oven
has been turned off.
•this is normal. The fan will automatically shut off when the oven is cooled.
•this is the cooling fan and is normal. The fan will continue to run after use until
the oven cools.
A fan sound
can be heard.
•fault codes are shown in the display as “F” and a number. If a fault code appears in
the display and beeps sound, press the CANCEL pad. If the fault code and beeps
continue after pressing cancel, disconnect power to the wall oven. Wait a few
minutes, then reconnect power to the oven. If the fault code and beeps still
continue, disconnect power to the wall oven and call an authorized servicer.
Fault Codes
• if the oven is heavily soiled, excessive flare-ups may result in a fault code during a
clean cycle. Press CANCEL pad and allow the oven to cool for one hour, then reset
the clean cycle. If the fault code and beeps still continue, disconnect power to the
appliance and call an authorized servicer.
17
If You Need Service
•
Call the dealer from whom your appliance was purchased or call Maytag Appliances Sales Company, Maytag
Customer Assistance at 1-800-688-9900, USA or 1-800-688-2002, CANADA to locate an authorized servicer.
•
•
Be sure to retain proof of purchase to verify warranty status. Refer to WARRANTY (last page) for further
information on owner’s responsibilities for warranty service.
If the dealer or service company cannot resolve the problem, write to Maytag Appliances Sales Company, Attn:
CAIR® Center, P.O. Box 2370, Cleveland, TN 37320-2370, or call 1-800-688-9900, USA or 1-800-688-2002,
CANADA.
U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.
NOTE: When writing or calling about a service problem, please include the following information:
a. Your name, address and telephone number;
b. Model number and serial number;
c. Name and address of your dealer or servicer;
d. A clear description of the problem you are having;
e. Proof of purchase (sales receipt).
•
User’s guides, service manuals and parts information are available from Maytag Appliances Sales Company,
Maytag Customer Assistance.
18
Maytag Wall Oven Warranty
Full One Year Warranty - Parts and Labor
For one (1) year from the original retail purchase date, any part which fails in normal home use will be repaired or replaced
free of charge.
Limited Warranties - Parts Only
Second Year - After the first year from the original purchase date, parts which fail in normal home use will be repaired or
replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage and transportation.
Third Through Fifth Year - From the original purchase date, parts listed below which fail in normal home use will be
repaired or replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage and
transportation.
•
•
Electronic Controls
Electric Heating Elements: broil and bake elements on electric cooking appliances.
Canadian Residents
The above warranties only cover an appliance installed in Canada that has been certified or listed by appropriate test agen-
cies for compliance to a National Standard of Canada unless the appliance was brought into Canada due to transfer of
residence from the United States to Canada.
Limited Warranty Outside the United States and Canada - Parts Only
For two (2) years from the date of original retail purchase, any part which fails in normal home use will be repaired or
replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage and transportation.
The specific warranties expressed above are the ONLY warranties provided by the manufacturer. These warranties give you
specific legal rights, and you may also have other rights which vary from state to state.
What is Not Covered By
These Warranties:
4. Products purchased for commercial or industrial use.
1. Conditions and damages resulting from any of the
following:
5. The cost of service or service call to:
a. Correct installation errors.
a. Improper installation, delivery, or maintenance.
b. Any repair, modification, alteration, or adjustment
not authorized by the manufacturer or an
authorized servicer.
b. Instruct the user on the proper use of the product.
c. Transport the appliance to the servicer.
6. Consequential or incidental damages sustained by any
c. Misuse, abuse, accidents, or unreasonable use.
d. Incorrect electric current, voltage, or supply.
e. Improper setting of any control.
person as a result of any breach of these warranties.
Some states do not allow the exclusion or limitation of
consequential or incidental damages, so the above
exclusion may not apply.
2. Warranties are void if the original serial numbers have
been removed, altered, or cannot be readily
determined.
3. Light bulbs.
MAYTAG • 403 West Fourth Street North • P.O. Box 39 • Newton, Iowa 50208
Form No. A/03/00
Part No. 8112P164-60
h t t p : / / w w w . m a y t a g . c o m
Litho U.S.A .
|