INSTRUCTION MANUAL
Random Orbit Sander
BO5040
BO5041
010741
DOUBLE INSULATION
IMPORTANT: Read Before Using.
1
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
6.
7.
Do not expose power tools to rain or wet
conditions. Water entering power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
a
Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
8.
9.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
17.8.2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
GEA005-3
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
medication.
A
moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
2.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
3.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
17. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
3
Power tool use and care
5.
6.
Ventilate your work area adequately when you
perform sanding operations.
Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
Use of this tool to sand some products, paints
and wood could expose user to dust
containing hazardous substances. Use
appropriate respiratory protection.
Be sure that there are no cracks or breakage
on the pad before use. Cracks or breakage
may cause a personal injury.
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
19. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
20. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
7.
8.
SAVE THESE INSTRUCTIONS.
21. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
22. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
FUNCTIONAL DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
Switch action
1. Lock button
2. Switch trigger
Service
25. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
1
2
26. Follow instruction for lubricating and
changing accessories.
27. Keep handles dry, clean and free from oil and
010743
CAUTION:
•
•
Before plugging in the tool, always check to see
that the switch trigger actuates properly and returns
to the "OFF" position when released.
Switch can be locked in "ON" position for ease of
operator comfort during extended use. Apply
caution when locking tool in "ON" position and
maintain firm grasp on tool.
grease.
GEB021-4
SANDER SAFETY WARNINGS
1.
Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT safety
glasses.
2.
3.
Hold the tool firmly.
Do not leave the tool running. Operate the tool
only when hand-held.
This tool has not been waterproofed, so do not
use water on the workpiece surface.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and
push in the lock button and then release the switch
trigger.
4.
4
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
The front grip can be loosened and moved horizontally to
a desired working position. Once the front grip is in the
desired position, retighten before using.
Speed adjusting dial
For BO5041 only
Installing or removing the front grip
1. Speed adjusting
1. Screw
dial
2. Front grip
1
1
2
010744
010805
The tool speed can be infinitely adjusted between 4,000
and 12,000 orbit per minute by turning the adjusting dial.
Higher speed is obtained when the dial is turned in the
direction of number 5; lower speed is obtained when it is
turned in the direction of number 1.
Refer to the figure for the relationship between the number
settings on the adjusting dial and the kind of work.
A range: For polishing
Open the grip base, and attach it to the sander in the
area of the Makita logo.
1. Grip base
2. Makita logo
2
B range: For finish sanding
1
C range: For regular sanding
12000
010804
After closing the grip base, firmly tighten on the front grip
to the screw section of the grip base.
C
4000
B
A
1
2
3
4
5
Dial setting
003291
NOTE:
•
The figure shows standard applications. They may
differ under certain conditions.
010806
To remove, loosen and remove front grip, and then
remove grip base.
ASSEMBLY
CAUTION:
Installing or removing abrasive disc
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
How to use the front grip
010745
To install the abrasive disc, first remove all dirt or foreign
matter from the pad. Then peel off the backing paper
from the abrasive disc and attach the abrasive disc to the
010809
5
pad. Be careful to align the holes in the abrasive disc with
those in the pad.
Installing paper dust bag
2
1. Groove
2. Front fixing
cardboard
3. Front side of
paper dust bag
CAUTION:
1
•
If you peel off the abrasive disc from the pad, its
adhesion will become poor. Never attempt to stick it
onto the pad for further use.
Installing dust bag
3
1. Dust bag
003742
Place the paper dust bag on the paper dust bag holder
with its front side upward. Insert the front fixing cardboard
of the paper dust bag into the groove of the paper dust
bag holder.
1
1. Claws
2. Upper part
1
010746
Install the dust bag on the tool so that the Makita logo on
the dust bag will be upright (not upside down).
2
Emptying dust bag
1. Dust nozzle
003743
Then press the upper part of the front fixing cardboard in
arrow direction to hook it onto the claws.
1
1. Notch
2. Guide
003323
When the dust bag is about half full, switch off and unplug
the tool. Remove the dust bag from the tool. Then remove
the dust nozzle from the dust bag after unlocking the dust
nozzle by turning it slightly counterclockwise. Empty the
dust bag by tapping it lightly.
2
1
003744
1. Dust nozzle
1
003326
003745
After emptying the dust bag, install the dust nozzle on the
dust bag. Turn the dust nozzle slightly clockwise to lock it
in place. Then install the dust bag on the tool as
described in "Installing dust bag".
Insert the notch of the paper dust bag into the guide of
the paper dust bag holder. Then install the paper dust
bag holder set on the tool.
6
Installing paper filter bag
OPERATION
1. Holding tab
CAUTION:
•
Always use the front grip and firmly hold the tool by
front grip and switch handle during operations.
Sanding operation
1
009094
Make sure that the logo on the cardboard lip and the logo
on the dust box are on the same side, then install the
paper filter bag by fitting the cardbord lip in the groove of
each holding tab.
1. Dust box
010747
2. Dust nozzle
1
CAUTION:
•
•
Never run the tool without the abrasive disc. You
may seriously damage the pad.
Never force the tool. Excessive pressure may
decrease the sanding efficiency, damage the
abrasive disc or shorten tool life.
2
•
Using the tool with the pad edge contacting the
workpiece may damage the pad.
009095
Make sure that the logo on the cardboard lip and the logo
on the dust nozzle are on the same side, then install the
dust nozzle on the dust box.
Hold the tool firmly. Turn the tool on and wait until it
attains full speed. Then gently place the tool on the
workpiece surface. Keep the pad flush with the
workpiece and apply slight pressure on the tool.
Removing dust box and paper filter bag
1. Latch
2. Dust nozzle
CAUTION:
The sanding pad rotates clockwise during the loaded
operation, but it may rotate counterclockwise during the
no-load operation.
Polishing operation
For BO5041 only
2
1
CAUTION:
009092
•
•
•
Use only a Makita genuine sponge pad, felt pad or
wool pad (optional accessories).
Always operate the tool at low speed to prevent
work surfaces from heating abnormally.
Never force the tool. Excessive pressure may
decrease the polishing efficiency and cause motor
overload, resulting in tool malfunction.
Remove the dust nozzle by pushing the two latches.
009093
Remove the paper filter bag first by pinching the logo
side of its cardboard lip, then by pulling the cardboard lip
downwards to move it out of the holding tab of the dust
box.
7
1.
Applying wax
MAINTENANCE
1. Sponge pad
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
1
•
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
010803
Use an optional sponge pad. Apply wax to the
sponge pad or work surface. Run the tool at low
speed to smooth out wax.
NOTE:
ACCESSORIES
•
First, wax a not conspicuous portion of the work
surface to make sure that the tool will not scratch
the surface or result in uneven waxing.
CAUTION:
•
These
accessories
or
attachments
are
•
Always run the tool at low speed. Running it at high
speed may cause the wax to spatter.
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
2.
Removing wax
1. Felt pad
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Hook-and-loop type abrasive discs (with
pre-punched holes)
1
•
•
Hook-and-loop type sponge pad
Paper dust bag holder
(For BO5041 only)
010802
•
•
•
Hook-and-loop type felt pad
Hook-and-loop type wool pad
Paper dust bag
Use an optional felt pad. Run the tool at low speed
to remove wax.
3.
Polishing
1. Wool bonnet
1
010801
Use an optional wool pad. Run the tool at low
speed and apply the wool pad gently to the work
surface.
8
9
10
11
Makita Corporation Anjo, Aichi, Japan
884946-222
|