OOPPTT••2244
OPT•24
OOPPTT••2244
Installation Guide
24-Channel 24-bit ADAT Optical I/O Card for the HDR24/96 and MDR24/96
4) Remove the blank cover plate for the ACC1 slot (next to the SYNC card) by removing 1 Phillips-
head screw. Save the screw for installing the OPT•24.
4) Remove Screw and
ACC1 Slot Cover Plate
REAR PANEL
®
5) Unplug the 2 ribbon cables from the Sync card. Squeeze the tabs on the sides of the connectors and
gently wiggle from side to side to release them from their sockets.
5A) Unplug Ribbon Cables
from Sync Card
5B) Pull Ribbon Cables back
and out of the way
REAR PANEL
©
2 0 0 0
M
®
3
Installation Guide
6) Unplug both ends of the COM cable (040-383-00), located between the front panel Display board (A)
and the Card Cage board (B). Cable ties hold the COM cable in place. Leave the cable inside the
HDR24/96 in case the OPT•24 is ever removed and the COM cable needs to be reconnected.
6) Remove the COM Cable
from the Display Board (A)
and the Card Cage Board (B)
REAR PANEL
©
2 0 0 0
M
®
B
A
7) Connect the 2 short/fat ribbon cables (supplied) to the 2 bottom connectors (J3B and J4B, furthest
from the edge) on the OPT•24. The connectors have a keying tab in the center so they can’t be
plugged in wrong. It doesn’t matter which end of the ribbon cables you connect to the OPT•24.
J3B
J4B
8) Connect the 2 ribbon cables that you removed from the Sync card to the 2 top connectors (J3A and
J4A, closest to the edge) on the OPT•24. They will click in place when properly inserted.
8) Connect 2 Ribbon Cables
to OPT¥24 Board
REAR PANEL
OPT¥24 Board
I
4
9) Install the OPT•24 into the ACC1 PCI slot by carefully aligning the card’s gold-plated connector
edge to the PCI slot on the motherboard and pushing down gently but firmly until the card is fully
seated into the slot. It may help to gently rock the board front to back until the board is completely
seated.
Note: Make sure the loose connector ends are pointing up so they can be accessed for step 11.
9) Install OPT•24 Board
into the ACC1 PCI slot
10) Install Screw into
the OPT•24 bracket
REAR PANEL
I
®
10) Install the screw that you removed from the blank cover plate to secure the OPT•24 to the HDR chassis.
11) Connect the short ribbon cables from the OPT•24 card to the adjacent Sync card by folding them over the
top of the Sync card (see illustration below and on next page).
11) Connect the 2 short ribbon
cables to the Sync Card
REAR PANEL
®
5
Installation Guide
Front view of ribbon cable connections between the
Sync Card and the OPT•24
12) Install the supplied replacement COM cable.
a. Install the center connector to the Card Cage board.
b. Install the shorter end to the front panel Display board.
c. Install the longer end to the OPT•24 board.
REAR PANEL
12a) Install the replacement COM Cable:
Center connector to Card Cage Board
12c) Longer end to
OPT•24 Board
®
12b) Shorter end to Front
Panel Display Board
13) Replace the cover, reinstall the screws, and
you’re ready to go!
6
OPT•24
Selecting the OPT•24 I/O
This is done in the same way that you setup and
configure the other I/O cards—in the Digital I/O
Setup window (or by pressing the Digi-I/O button on
the front panel).
To select the OPT•24 from the front panel:
1. Press Digi-I/O to enter the Digital I/O Card
Setup screen.
To select the OPT•24 from the screen
(HDR24/96 only):
1. Select Setup from the Windows menu and
click the Digital I/O icon. The Digital I/O
Setup dialog box shows you the current
settings for each of the three I/O cards.
DISK UTIL SYSTEM DIGI-I/O
SYNC
DEC
2. Select In. The Setup Tape Inputs screen
shows you the current settings for each of the
three I/O cards.
DIGITAL I/O Card Setup
Stat Rate
In Out Bits Convert
3. Press the Select button corresponding to each
I/O card and toggle the selection to the
desired input source.
4. The OPT•24 outputs are always active, so no
configuration is necessary for the outputs.
5. When done, press the Digi-I/O button to exit
the menu.
2. Click the Input pulldown menu and select the
input source you want to use for each I/O
card.
3. The OPT•24 outputs are always active, so no
configuration is necessary for the outputs.
IN 17-24
OUT 17-24
IN 9-16
OUT 9-16
IN 1-8
OUT 1-8
“Mackie,” the “Running Man” figure, and “OPT•24”
are trademarks or registered trademarks of Mackie
Designs Inc. All other brand names mentioned are
trademarks or registered trademarks of their
respective holders, and are hereby acknowledged.
OPT•24 Inputs and Outputs
© 2002 Mackie Designs Inc.
All Rights Reserved.
Printed in the U.S.A.
7
Installation Guide
16220 Wood-Red Rd. NE • Woodinville, WA 98072 • USA
US & Canada: 800/898-3211
Europe, Asia, Central & South America: 425/487-4333
Middle East & Africa: 31-20-654-4000
E-mail: [email protected]
|