Kodak All in One Printer KY0730485 User Manual

Matchprint  
Professional Server v3.0  
for Xerox DocuColor 12 Printer/Copier  
Quick Start  
Part number - KY0730485  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Table of Contents  
QUICK START STEPS................................................................. 7  
STEP 1. STARTING THE SOFTWARE .......................................... 7  
STEP 2. PRINTER SETUP........................................................... 7  
STEP 3. PRINTER CALIBRATION............................................... 9  
Spectrocam Setup.............................................................................10  
Calibration Procedure ........................................................................10  
Scanner...................................................................................................13  
Spectrocam .............................................................................................13  
Spectrocam TIPs...............................................................................16  
STEP 4. ADDING A SPOOLER .................................................. 17  
STEP 5. ADDING A HOT FOLDER ............................................. 19  
STEP 6. SETTING PREFERENCES ............................................. 21  
STEP 7. INSTALLING PPDS ..................................................... 25  
STEP 8. JOB PRINTING........................................................... 25  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
3
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Product Safety and Compliance  
Warning!  
Do not modify or use any AC power cord other than the one included with  
shipping.  
In some cases, the supplied power cord may not be compatible with the AC  
wall outlet in your region. If this is true, you must obtain a suitable power cord  
that meets the following criteria:  
The cord must be rated for use at the AC voltage available, with a current  
rating that is at least 125% of the current rating of the product.  
The AC plug end must be terminated in a grounding-type male plug designed  
for use in your region. The plug ends must be labeled or marked to indicate  
they have been certified by an agency acceptable in your region.  
The connector at the product end must be an IEC 320, sheet C13, female  
connector (or the equivalent EN 60 320 connector.)  
The cord must be less than 14.8 feet (4.5 meters) long and, for use in Europe,  
be created with <HAR> (harmonized) or VDE certified cordage.  
Warning!  
1. The user must never remove chassis covers. Some system circuitry retains  
voltage even when the system is turned off. Only qualified service technicians  
should remove chassis covers.  
2. There are no user-serviceable components in the KPG server. Refer all  
system repair to a qualified service technician.  
Warning!  
The power supply voltage standby circuit is active when the computer is  
turned off. Ensure that the computer is disconnected from its power source  
and from all telecommunication links, networks, or modem lines whenever the  
chassis cover is removed. Do not operate the computer with the cover  
removed. Only qualified service technicians should remove chassis covers if  
repair or component replacement is required.  
Warning!  
Danger of explosion if the battery is incorrectly replaced. Replace only with  
the same or equivalent type recommended by the equipment manufacturer.  
Discard used batteries according to manufacturer's instructions.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
4
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Sécurité et conformité du produit  
Avertissement !  
Ne modifiez ni n'utilisez aucun câble d'alimentation CA autre que celui qui vous  
a été livré avec le produit.  
Il peut arriver, dans certaines régions, que le câble d'alimentation fourni ne  
soit pas compatible avec la prise de courant murale. Si tel est le cas, procurez-  
vous un câble d'alimentation adapté conforme aux critères suivants :  
La puissance du câble doit correspondre à la tension CA disponible, avec un  
courant nominal d'au moins 125 % du courant nominal du produit.  
Le câble CA doit avoir à son extrémité de branchement une fiche de terre mâle  
conçue et adaptée pour un usage dans votre région. Les fiches doivent être  
dotées d'une étiquette indiquant qu'elles ont été certifiées par une agence  
reconnue dans votre région.  
Le connecteur à l'extrémité du produit doit être de type femelle IEC 320,  
blindé C13 (ou équivalent EN 60 320).  
Le câble doit avoir une longueur maximum de 14,8 pieds (soit 4,5 mètres) et,  
en Europe, doit avoir été fabriqué à base de filin certifié <HAR> (norme  
harmonisée) ou VDE.  
Avertissement !  
1. L'utilisateur ne doit jamais ôter le couvercle du châssis. Certains circuits  
continuent d'être alimentés lorsque le système est hors tension. Seuls des  
techniciens de service qualifiés sont habilités à ôter le capot du châssis.  
2. Aucun composant du serveur Professional ne peut être réparé par  
l'utilisateur. Tout dépannage doit être effectué par un technicien de service  
qualifié.  
Avertissement !  
Le circuit de réserve de tension d'alimentation reste actif lorsque l'ordinateur  
est éteint. Assurez-vous que l'ordinateur est débranché et que tous les  
réseaux, liaisons de télécommunications ou lignes de modem sont déconnectés  
lorsque le couvercle du châssis doit être ôté. Ne tentez jamais de faire  
fonctionner l'ordinateur tant que le couvercle n'est pas remis en place. Seuls  
des techniciens de service qualifiés sont habilités à ôter le couvercle du châssis  
si des réparations s'avèrent nécessaires ou qu'il est indispensable de  
remplacer des composants.  
Avertissement !  
Danger d'explosion si la batterie n'est pas parfaitement remise en place.  
Remplacez une batterie usée uniquement par le même type ou un type  
équivalent recommandé par le fabricant de l'appareil. Mettez les batteries  
usées au rebut conformément aux instructions du fabricant.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
5
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Service Information  
Contact your Xerox representative for technical support or product related questions.  
Agency Approvals  
U.S.  
FCC Class A required, FCC Class B preferred  
UL 1950 standard testing  
Canada  
Europe  
Canadian EMI Class A  
CSA 950  
CISPR 22 Class B  
CE Mark  
EN 60950 LUD  
The radiated and conducted emissions are per EN 55022 class B limits.  
The radiated and conducted immunity are per EN 55024 class B limits.  
For European safety, EN60950 under 73/23/EEC, Low Voltage Directive (LVD)  
amendment is correct.  
Documentation  
Online Help  
Please refer to the Matchprint Professional Server (MPS) online help for  
more information on using new and existing features of the application.  
To access the online help, launch the MPS application, then go to Help >  
Read the User Guide.  
Printable PDF of User’s Guide  
There is also a user guide.pdf located on the application’s CD-ROM.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
6
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Quick Start Steps  
To quickly get your system set up for printing from the client, go through the  
following procedures listed in the order shown:  
Steps:  
1. Start the Matchprint Professional Server software.  
2. Printer Setup.  
3. Printer Calibration.  
4. Add a Spooler.  
5. Add a Hot Folder.  
6. Set Preferences.  
7. Install PPDs.  
8. Job Printing. You should now be able to successfully print from your client  
application to the DocuColor 12.  
Step 1. Starting the Software  
1. Double-click the Matchprint Professional Server software icon.  
2. The Matchprint Professional Server main application window appears.  
Step 2. Printer Setup  
The software is shipped to you with the Printer Settings already set. However, you  
should confirm that the Media Settings (media type and size) for each tray match  
what is in your DocuColor 12.  
Note: If the printer is deleted, you will need to perform the following printer  
setup instructions.  
To add a printer or change printer settings, complete the following steps:  
1. If you have had previous versions of the Matchprint Professional Server  
on your system, delete previous printers prior to adding new ones. If the  
system asks you if you want to delete previous files used only with this  
printer, select Yes.  
2. Go to Printer > Add Printer or select Xerox DocuColor 12 (or the name of  
the printer you need to change). The Printer Settings window displays:  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
7
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
3. Confirm the desired Printer Options:  
Active: Make sure this is checked. This ensures the printer is available to the  
MPS RIP.  
More Options... Not currently used.  
Calibration...: Go to the Printer Calibration section for more information on  
this topic.  
Page Alignment...: Contains instructions on how to adjust Page Alignment.  
CMYK Count, Gray Count, and Proof Count: Displays the current print  
totals for those categories. The Proof Count can be reset to zero by clicking  
on the Reset Proof Count button.  
4. Confirm the desired Media Settings for each tray and click OK.  
The contents of each tray can vary from site to site, however standard tray  
setup is as follows:  
Tray 1: Media Type - Normal Bond, Media Size - Letter (8.5 x 11 inches)  
Tray 2: Media Type - Normal Bond, Media Size - Letter SEF (11 x 8.5  
inches)  
Tray 3: Media Type - Normal Bond, Media Size - Legal (8.5 x 14 inches)  
Tray 4: Media Type - Normal Bond, Media Size - Tabloid (11 x 17 inches)  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
8
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Tray 6 (High Capacity Feeder) – Optional: Media Type - Normal Bond,  
Media Size - Letter (8.5 x 11 inches)  
Notes:  
Tray 5 is a manual feed tray located on the left side of the Xerox  
DocuColor 12. (Tray 5 is not configured here.)  
Load paper so the watermark wording is face down in the tray.  
The DocuColor 12 can be set to disable automatic tray switching,  
however the Matchprint Professional Server overrides this setting if  
the job's parameters are set to Automatically Select the input  
tray. Go to the Setting Job Parameters, Printer tab in the online  
help or the user guide.pdf for more information.  
Step 3. Printer Calibration  
KPG recommends daily calibration and recalibration each time the printer is serviced.  
Calibrate for Bond medias using the following Xerox Color Xpressions media. When  
using supplied profiles and device links for premium medias, printer calibration must  
use the Matchprint Co-Branded Xerox Color Laser Proofing Paper. This is the only  
premium paper authorized by KPG and Xerox to accurately simulate Matchprint color.  
The Color Profiles and Device Links supplied for normal, heavyweight, and extra  
heavyweight bond were all created using the following Xerox media:  
Normal Bond: Xerox Color Xpressions 24 lb., Bright White 96 paper.  
Heavyweight Bond: Xerox Color Xpressions 60 lb., Bright White 96 paper.  
Extra Heavyweight Bond: Xerox Color Xpressions 80 lb., Bright White 98  
paper.  
Important! If a media other than the recommended Xerox media is used, the  
following error appears: “Warning! The media used for calibration appears to be  
significantly different from the Normal Bond (or Heavyweight) media recommended  
for used with this application. Results of the calibration on this media may not be  
typical.”  
Printer calibration can be performed internally by using the DocuColor 12 built-in  
scanner or by using the Spectrostar Spectrocam, an external measurement device.  
Both procedures are described in this section. If calibration is to be performed using  
the Spectrocam, please go through the following Spectrocam Setup instructions  
before beginning the calibration process.  
If calibration is to be performed using the DocuColor 12 scanner, please skip to the  
section titled, Calibration Procedure.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
9
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Spectrocam Setup  
1. Shut down the computer.  
2. Connect the Spectrocam to the COM 1 (or appropriate) serial port on the back  
of the Matchprint Professional Server.  
3. Plug the Spectrocam power connector into the AC adapter and then plug the  
AC adapter into a power outlet.  
4. Power on the computer.  
5. Launch the Matchprint Professional Server software.  
Note: Always disconnect the Spectrocam from the AC power supply before  
removing the Spectrocam from the Matchprint Professional Server.  
Calibration Procedure  
1. From the Printer menu, select XeroxDocuColor 12 (or the name of the  
printer requiring calibration). The Printer Settings window displays.  
2. Click on Calibration to display menu selections Perform Printer  
Calibration and Printer Calibration Setup.  
3. Select Printer Calibration Setup to display the following setup screen:  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
10  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
4. Select a specific media, then enter how often the printer requires calibration  
for that particular media. Repeat this process for each media.  
The Last Calibration column displays the time elapsed since a particular  
media has been calibrated. Uncalibrated medias display "n/a" in this column.  
If the time elapsed is longer than the calibration interval, the "Calibrated?"  
column will read "No."  
Note: Selecting the Reset button, nullifies the most recent calibration and  
returns the selected media to its default setting.  
5. Click OK.  
6. From the Calibration menu, select Perform Printer Calibration. The  
following screen appears:  
Note: The calibration process cannot be started until all active jobs in the  
queue have finished printing.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
11  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
7. From the Device drop-down list box, choose either the DocuColor 12  
Scanner or the Spectrocam Device.  
8. From the Media Type drop-down list box, select the media to be calibrated.  
Note: Transparency media cannot be calibrated.  
9. From the Media Size drop-down list box, select the media size on which to  
print the calibration form.  
10.From the Tray drop-down list box, select the input tray containing the  
specified media.  
The input tray can be specified if the user wants to calibrate the media  
contained in a specific tray of the DocuColor 12. An Automatic selection  
chooses the input tray if no input tray is specified. If ExtraHeavyweight or a  
KPG/Xerox co-branded media is selected, the input tray defaults to Manual  
Feed. In this case, the user is not able to change the input tray.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
12  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
11.Click on Print Test Form button. A progress bar appears as the form prints:  
12.When the form printing is complete:  
Go to Scanner for scanner calibration.  
Go to Spectrocam for Spectrocam calibration.  
Scanner  
1. Place the calibration form on the platen of the DocuColor 12 and click  
Calibrate.  
2. If the calibration is successful, the screen display says, "The calibration  
process was successful. You may now calibrate another media."  
3. Click OK to go back to the calibration window.  
Note: If the calibration process fails, check to make sure the test page is  
properly positioned on the platen. The scanable area is 11"x 17". If the  
calibration test form is outside this area, calibration will fail.  
Spectrocam  
1. Place the test form and ruler on the black scanner plate and position the  
measurement device on the first patch on the upper, left corner.  
2. Click on the Calibrate button.  
If the Spectrocam was not previously calibrated, a prompt directs you to  
measure/remeasure the white reference. Place the measurement device on the  
white target reference and touch the green sensor. After remeasuring the white  
reference, reposition the measurement device on the first patch on the upper  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
13  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
left corner of the test form.  
Important Note on Calibrating the Spectrocam: Each Spectrocam  
needs to be calibrated against its own unique White Reference Target before  
taking measurements. The Spectocam and its White Reference have  
matching serial numbers. For additional information, please see the  
Spectrocam user documentation.  
3. Touch the green sensor and move the device slowly across the first row.  
When you complete the first row, reposition the Spectrocam over the first  
patch of the second row and touch the green sensor again to begin measuring  
the second row. Continue in this fashion until all rows are read.  
Patches are read from left to right in a slow, steady manner. The color  
patches appear on the screen as they are measured. It should take  
approximately 6 to 8 seconds to completely scan one row.  
If you move too slowly or too rapidly, patches are not read correctly. Within  
the calibrate dialog an X appears on any patch that is miss-read. If this  
happens, reposition the device on the first patch of that row and touch the  
sensor to start the patch reading of that row again. The Instruction box at the  
top of the window will indicate any action you must take regarding  
measurement readings.  
To read the last two rows, you will need to move the test form up so the  
Spectrocam rests on the black scanner plate.  
Note: The Spectrocam times out after 10 minutes of inactivity. Instructions  
appear directing the user to restart the calibration process.  
If the calibration is successful, the following message appears: "The calibration  
process was successful. You may now calibrate another media."  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
14  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
4. Click on OK to return to the calibration window.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
15  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Spectrocam TIPs  
Calibrating the Spectocam  
Make sure the Spectrocam is calibrated with the white target reference that  
was shipped with your Spectrocam. The serial numbers on the bottom of the  
white target reference target and the Spectrocam must match. Setting the  
white reference to a different target can result in inaccurate printed color.  
When measuring on the white target reference, be sure the device is seated  
correctly.  
Scanning the Test Form  
Make sure the printed test form is properly aligned to the black scan plate.  
The Spectrocam must start inside the first patch directly in the center.  
Otherwise, patches will be read incorrectly.  
Make sure the Spectrocam is securely seated in the guide ruler and not tipped  
while you read patches. Tipping or miss-aligning the Spectrocam while on the  
guide ruler will cause errors.  
The green sensor on top of the Spectrocam responds to transitions from light  
to dark. The sensor must be activated to measure each row. Inadvertently  
covering the sensor can prematurely initiate the measurement sequence.  
Listen for the flashlamp before you move off the first patch. Sometimes there  
is a slight delay before it begins to measure.  
Reading patches too rapidly is a common error. Scanning one row should take  
about 6 to 8 seconds.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
16  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Step 4. Adding a Spooler  
Creating a spooler allows workstations to see the proofer over the network as a  
custom printer with its own user definable configurations. Files that are sent to the  
spooler are automatically entered into the Job Queue for proofing.  
Note for Windows NT and 2000: At the client Windows machine, either log  
into the same domain as the Matchprint Professional Server, or connect to the  
Matchprint Server with a valid user name and password that has a minimum of  
read access. For security purposes, KPG does NOT recommend enabling the  
Guest Account.  
Failure to do so will result in Windows 2000 clients receiving the following error  
message when trying to print an image: "Could not complete the print command  
because the selected printer driver could not be found. Please select a printer  
from the control panel and try again."  
1. Go to Input > Add Spooler. The Enter Spooler Name window displays:  
2. Enter a spooler name. (This name is what client users will see when they  
select a printer on the network.)  
Note: When creating a spooler to be used in a mixed Operating System  
environment, remember that Windows 98 require the spooler name to be  
12 characters or less. (Alpha-numeric characters and spaces are allowed.)  
3. Click OK. The Input Method window displays:  
4. Make sure Active is checked. (The default setting is for Active to be  
checked.)  
5. Click on the parameter tabs and enter the Spooler configuration. When the  
file enters this Spooler, it is given these default settings.  
6. When parameter information is complete, click OK to apply these settings.  
Note: For PostScript jobs submitted via a Print File, job parameter settings  
for Number of Copies, Input Tray and Media Type override the PostScript  
file codes. For all other settings, the PostScript file settings override the job  
parameter settings.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
17  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
For jobs submitted through a spooler or hot folder, the values in the  
Postscript file always override the default job parameters for that spooler or  
hot folder.  
The spooler will now appear in the drop-down list box under the Input menu  
selection. You can access and change spooler parameters by selecting it from this  
list.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
18  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Step 5. Adding a Hot Folder  
Hot Folders are folders the Matchprint Professional Server software "watches" for  
incoming job files. When a recognized file is placed into a Hot Folder, it is  
automatically entered into the job queue for printing.  
Important! Files are automatically deleted from a Hot Folder after  
successfully printing. Do not place original files into Hot Folders. Always "copy"  
files to a Hot Folder.  
1. Go to Input > Add Hot Folder. A browser window displays:  
2. You may select an existing folder or create a new folder. (Create a new folder  
by navigating to the location where you want the folder. At the end of the  
path string type \xxx [where xxx is the new folder name], then click OK.  
Answer Yes to the question, "Do you want the folder to be created?")  
The Input Method settings window displays:  
3. Make sure Active is checked. (The default setting is for Active to be  
checked.)  
4. Under the More Options button, enter the Poll Interval seconds to set how  
often this Hot Folder will be checked for jobs. (Default setting is 10 seconds.)  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
19  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
5. Click on the parameter tabs to enter Hot Folder custom configurations. When  
the file enters this Hot Folder, it is given these default settings. Click OK to  
continue.  
6. When all parameter settings are complete, click OK to apply these settings.  
Note: For PostScript jobs submitted via a Print File, job parameter settings  
for Number of Copies, Input Tray and Media Type override the PostScript  
file codes. For all other settings, the PostScript file settings override the job  
parameter settings.  
For PostScript jobs submitted through a spooler or hot folder, the values in  
the PostScript file always override the default job parameters for that  
spooler or hot folder.  
The hot folder will now appear in the drop-down list box under the Input menu  
selection. You can access and change the hot folder parameters by selecting it from  
this list.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
20  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Step 6. Setting Preferences  
Go to File > Options > Preferences. The File Preferences dialog box displays.  
The Preferences dialog contains four tabs: General, Cache, Paths and Roles.  
General Tab  
The General tab allows you to customize how sizes are displayed in the File  
Information and Job Parameters subsets, and to customize the Job Slug  
Options.  
Display Units allows you to set inches, centimeters, or pixels. This setting  
customizes how sizes are displayed in the File Information and Job Parameter  
subsets.  
Language allows you to select English, French, Italian, German, or Spanish  
languages. You need to restart the software for a language change to take  
affect.  
Job Slug Options allows you to selectively display document name, user  
name, media type, color target, page number and job ID. The Job Slug is an  
optional block of information that can be added to your proofs. (See Setting  
Job Parameters.)  
Automatic Media Size Conversion allows US size documents (e.g. Letter,  
Tabloid, TabloidExtra) to be printed on corresponding metric-sized paper, and  
visa versa. Select None, Convert Metric to English or Convert English to  
Metric. Conversion is available for the following page sizes:  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
21  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Note: This feature only works for PostScript files. For all other job  
types, media size must be selected on the Printer tab while setting  
Job Parameters.  
Metric Media Size  
US Media Size  
Letter  
A4  
A3  
Tabloid  
SRA  
TabloidExtra  
Print on Best Available Media allows jobs to print to the next best page size  
(larger) than the size configured in the printer setup. If Print on Best  
Available Media is not selected, the job goes into a "waiting for media" status  
and a message displays indicating what size media the job is expecting.  
Cache Tab  
The Cache tab allows you to customize how long files will be kept before being  
purged based on age, total size, or both.  
1. Enter the number of days and/or megabytes the Spooled Job files should be  
saved. (The default is 14 days or when 2000 MB is exceeded.) When the size  
limit is exceeded, the fewest possible files (oldest first) are deleted.  
2. Enter the number of days and/or megabytes the RIP'ed Job files should be  
saved. (The default is 14 days or when 2000 MB is exceeded.) When the size  
limit is exceeded, the fewest possible files (oldest first) are deleted.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
22  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Paths Tab  
The Paths tab allows you to change the location of Saved Jobs, Temporary  
Files, RIP'ed Pages and Archive Jobs Default.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
23  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Roles Tab  
The Roles tab allows you to enable roles for Administrator, Operator, or Guest.  
Each role allows the user to perform various tasks with the program. Refer to  
User Roles for more information on Role Management and Role Passwords.  
Administrator can perform all functions in the program. A password  
is required.  
Operator can perform most functions except configuration. A  
password is required.  
Guest has read-only access to the program. No password is required.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
24  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
Step 7. Installing PPDs  
Once the software is installed, Postscript Printer Driver (PPD) installation may be  
necessary to allow client Macintosh or PC computers to properly print to the Xerox  
DocuColor 12 copier over the network.  
Refer to the online user information for PPD installation information:  
1. Go to Help > Read the User’s Guide.  
2. In the navigator bar of the online user information, go to Installing the  
Software > Installing PPDs on Client Machines.  
3. Locate the PPD information for your client machine.  
Step 8. Job Printing  
You can print individual jobs from the Matchprint Professional Server, print from a  
Hot Folder, or print from a Spooler setup on the network.  
To print to a Hot Folder or Spooler:  
Simply drag-and-drop the file(s) to the Hot Folder or Spoolers you’ve created. The  
files will print using the parameter setup you designated.  
To print a job from the Matchprint Professional Server:  
1. Go to File > Print File.. from the menu. A file selection dialog box displays.  
2. Browse to the file you want to print, select the file and then click Open.  
The Print File dialog box displays with the following tabs:  
3. Set your parameters or use the default settings. For an explanation of tab  
information, go to the Setting Job Parameters topic, located in the online  
help.  
Notes:  
For PostScript jobs submitted via a Print File, job parameter settings for  
Number of Copies, Input Tray and Media Type override the PostScript file  
codes. For all other settings, the PostScript file settings override the job  
parameter settings.  
For jobs submitted through a spooler or hot folder, the values in the  
Postscript file always override the default job parameters for that spooler or  
hot folder.  
Printing Multiple Files  
To print more than one file:  
1. Locate the files on the hard drive and select them. (Use the Shift or Ctrl key  
to select multiple files.)  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
25  
 
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start  
2. Drag the selected files onto the Professional Server icon or the Job Queue  
window. A Print File dialog is displayed for the selected files. Select the  
desired options common to the files and click OK.  
3. The files now enter the job queue. Highlight individual jobs and change  
parameters, if desired.  
2002 Kodak Polychrome Graphics. All Rights Reserved.  
26  
 
CALL TOLL-FREE 1-877-KPGraphics (1-877-574-7274), EXT. 411 FOR ADDITIONAL INFORMATION.  
Because of our constant endeavor to improve quality and design, modifications may be made to products from time to  
time. Details of stock availability and specifications given in this publication are subject to change without notice. All  
weights and dimensions are approximate. © 2002 Kodak Polychrome Graphics. All rights reserved. Prepared and  
printed using materials manufactured and marketed by Kodak Polychrome Graphics. Matchprint is a trademark of Kodak  
Polychrome Graphics. Kodak is a trademark of Eastman Kodak Company. Other trademarks and registered trademarks  
used herein are the property of their respective owners.  
October 2002. Revision A, MPS V3.0  
 

Ingersoll Rand Patio Heater 651747 X B User Manual
Intel Computer Hardware SBC 780 User Manual
Intel Network Router 811 User Manual
JL Audio Car Stereo System 1000 1 User Manual
Johnson Controls Humidifier AVC Series User Manual
JVC DVD VCR Combo 0905TNH FN FN User Manual
JVC Home Theater System TH G10 User Manual
JVC Switch LVT1650 001B User Manual
Kenwood Stereo System VR 7070 User Manual
Keys Fitness Hot Tub BS 9101 User Manual